Translations by minwook shin

Unmounting and ejecting CD-ROM...

Tune CD-ROM drive parameters with hdparm?

The installer can use hdparm to tune some CD-ROM drive parameters, which may significantly speed up reading packages from the CD. You can change the parameters to be used. To disable hdparm, enter an empty parameter list.

No Ethernet card was detected, but a FireWire interface is present. It's possible, though unlikely, that with the right FireWire hardware connected to it, this could be your primary Ethernet interface.

Activate Serial ATA RAID devices?

One or more drives containing Serial ATA RAID configurations have been found. Do you wish to activate these RAID devices?

Modules to load:

The following Linux kernel modules were detected as matching your hardware. If you know some are unnecessary, or cause problems, you can choose not to load them. If you're unsure, you should leave them all selected.

The module ${MODULE} failed to load. You may need to pass parameters to the module to make it work; this is common with older hardware. These parameters are often I/O port and IRQ numbers that vary from machine to machine and cannot be determined from the hardware. An example string looks something like "irq=7 io=0x220"

If you don't know what to enter, consult your documentation, or leave it blank to not load the module.

Load missing drivers from removable media?

A driver for your hardware is not available. You may need to load drivers from removable media, such as a USB stick, or driver floppy.

If you have such media available now, insert it, and continue.

Load missing firmware from removable media?

Some of your hardware needs non-free firmware files to operate. The firmware can be loaded from removable media, such as a USB stick or floppy.

The missing firmware files are: ${FILES}

Networking can either be configured by DHCP or by manually entering all the information. If you choose to use DHCP and the installer is unable to get a working configuration from a DHCP server on your network, you will be given the opportunity to configure your network manually after the attempt to configure it by DHCP.

Your system has multiple network interfaces. Choose the one to use as the primary network interface during the installation. If possible, the first connected network interface found has been selected.

Attempting to find an available wireless network failed.

${iface} is a wireless network interface. Please enter the name (the ESSID) of the wireless network you would like ${iface} to use. To skip wireless configuration and continue, leave this field blank.

If your WEP key is in the format of a passphrase, prefix it with 's:' (without quotes).

Invalid WEP key

An error occurred and the network configuration process has been aborted. You may retry it from the installation main menu.

You may need to load a specific module for your network card, if you have one. For this, go back to the network hardware detection step.

Ad-hoc network (Peer to peer)

Wireless networks are either managed or ad-hoc. If you use a real access point of some sort, your network is Managed. If another computer is your 'access point', then your network may be Ad-hoc.

Wireless network configuration

Point-to-Point Protocol

ISDN Point-to-Point Protocol

Storing network settings...

Configure the network

Network autoconfiguration has succeeded

The DHCP configuration process has been aborted.

Retry network autoconfiguration

Retry network autoconfiguration with a DHCP hostname

Configure network manually

Network configuration method:

From here you can choose to retry DHCP network autoconfiguration (which may succeed if your DHCP server takes a long time to respond) or to configure the network manually. Some DHCP servers require a DHCP hostname to be sent by the client, so you can also choose to retry DHCP network autoconfiguration with a hostname that you provide.

The network autoconfiguration was successful. However, no default route was set: the system does not know how to communicate with hosts on the Internet. This will make it impossible to continue with the installation unless you have the first installation CD-ROM, a 'Netinst' CD-ROM, or packages available on the local network.

Reconfigure the wireless network

Point-to-point address:

The point-to-point address is used to determine the other endpoint of the point to point network. Consult your network administrator if you do not know the value. The point-to-point address should be entered as four numbers separated by periods.

Netmask:

The netmask is used to determine which machines are local to your network. Consult your network administrator if you do not know the value. The netmask should be entered as four numbers separated by periods.

Unreachable gateway

You may have made an error entering your IP address, netmask and/or gateway.

Currently configured network parameters: