|
|
91.
|
|
|
Booting from Firmware
|
|
|
Tag: title
|
|
|
|
|
(no translation yet)
|
|
|
|
Located in
boot-installer.xml:616
|
|
|
92.
|
|
|
There is an increasing number of consumer devices that directly boot from a flash chip on the device. The installer can be written to flash so it will automatically start when you reboot your machines.
|
|
|
Tag: para
|
|
|
|
|
(no translation yet)
|
|
|
|
Located in
boot-installer.xml:622
|
|
|
93.
|
|
|
In many cases, changing the firmware of an embedded device voids your warranty. Sometimes you are also not able to recover your device if there are problems during the flashing process. Therefore, please take care and follow the steps precisely.
|
|
|
Tag: para
|
|
|
|
|
(no translation yet)
|
|
|
|
Located in
boot-installer.xml:628
|
|
|
94.
|
|
|
Booting the NSLU2
|
|
|
Tag: title
|
|
|
|
|
(no translation yet)
|
|
|
|
Located in
boot-installer.xml:639
|
|
|
95.
|
|
|
There are three ways how to put the installer firmware into flash:
|
|
|
Tag: para
|
|
|
|
|
(no translation yet)
|
|
|
|
Located in
boot-installer.xml:640
|
|
|
96.
|
|
|
Using the NSLU2 web interface
|
|
|
Tag: title
|
|
|
|
|
(no translation yet)
|
|
|
|
Located in
boot-installer.xml:646
|
|
|
97.
|
|
|
Go to the administration section and choose the menu item <literal>Upgrade</literal>. You can then browse your disk for the installer image you have previously downloaded. Then press the <literal>Start Upgrade</literal> button, confirm, wait for a few minutes and confirm again. The system will then boot straight into the installer.
|
|
|
Tag: para
|
|
|
|
|
(no translation yet)
|
|
|
|
Located in
boot-installer.xml:647
|
|
|
98.
|
|
|
Via the network using Linux/Unix
|
|
|
Tag: title
|
|
|
|
|
(no translation yet)
|
|
|
|
Located in
boot-installer.xml:658
|
|
|
99.
|
|
|
You can use <command>upslug2</command> from any Linux or Unix machine to upgrade the machine via the network. This software is packaged for Debian. First, you have to put your NSLU2 in upgrade mode: <orderedlist> <listitem><para> Disconnect any disks and/or devices from the USB ports. </para></listitem> <listitem><para> Power off the NSLU2 </para></listitem> <listitem><para> Press and hold the reset button (accessible through the small hole on the back just above the power input). </para></listitem> <listitem><para> Press and release the power button to power on the NSLU2. </para></listitem> <listitem><para> Wait for 10 seconds watching the ready/status LED. After 10 seconds it will change from amber to red. Immediately release the reset button. </para></listitem> <listitem><para> The NSLU2 ready/status LED will flash alternately red/green (there is a 1 second delay before the first green). The NSLU2 is now in upgrade mode. </para></listitem> </orderedlist> See the <ulink url="http://www.nslu2-linux.org/wiki/OpenSlug/UsingTheBinary">NSLU2-Linux pages</ulink> if you have problems with this. Once your NSLU2 is in upgrade mode, you can flash the new image: <informalexample><screen> 
sudo upslug2 -i di-nslu2.bin
</screen></informalexample> Note that the tool also shows the MAC address of your NSLU2, which may come in handy to configure your DHCP server. After the whole image has been written and verified, the system will automatically reboot. Make sure you connect your USB disk again now, otherwise the installer won't be able to find it. |
|
|
Tag: para
|
|
|
represents a line break.
Start a new line in the equivalent position in the translation.
|
|
|
|
|
(no translation yet)
|
|
|
|
Located in
boot-installer.xml:659
|
|
|
100.
|
|
|
Via the network using Windows
|
|
|
Tag: title
|
|
|
|
|
(no translation yet)
|
|
|
|
Located in
boot-installer.xml:720
|
