Browsing Low German translation

Don't show this notice anymore
Before translating, be sure to go through Ubuntu Translators instructions and Low German guidelines.
110 of 10 results
1.
Could not access drive %1.
The drive is still busy.
Wait until it is inactive and then try again.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Keen Togriep op Loopwark %1.
Dat Loopwark hett noch to doon.
Versöök dat bitte nochmaal, wenn dat nich mehr aktiv is.
Translated and reviewed by Sönke Dibbern on 2006-05-04
Located in kio_floppy.cpp:200
2.
Could not write to file %1.
The disk in drive %2 is probably full.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Nich mööglich, na Datei "%1" to schrieven.
Wohrschienlich is de Diskett in't Loopwark %2 vull.
Translated and reviewed by Sönke Dibbern on 2006-05-04
Located in kio_floppy.cpp:204 kio_floppy.cpp:1144
3.
Could not access %1.
There is probably no disk in the drive %2
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Keen Togriep op %1.
Wohrschienlich is keen Diskett in't Loopwark %2.
Translated and reviewed by Sönke Dibbern on 2006-05-04
Located in kio_floppy.cpp:214
4.
Could not access %1.
There is probably no disk in the drive %2 or you do not have enough permissions to access the drive.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Keen Togriep op %1.
Wohrschienlich is keen Diskett in't Loopwark %2, oder Du hest dor nich noog Verlöven för.
Translated and reviewed by Sönke Dibbern on 2006-05-04
Located in kio_floppy.cpp:218
5.
Could not access %1.
The drive %2 is not supported.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Keen Togriep op %1.
Dat Loopwark %2 warrt nich ünnerstütt.
Translated and reviewed by Sönke Dibbern on 2006-05-04
Located in kio_floppy.cpp:222
6.
Could not access %1.
Make sure the floppy in drive %2 is a DOS-formatted floppy disk
and that the permissions of the device file (e.g. /dev/fd0) are set correctly (e.g. rwxrwxrwx).
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
There are leading/trailing spaces here. Each one represents a space character. Enter a space in the equivalent position in the translation.
Keen Togriep op %1.
Bitte prööv, wat de Diskett in't Loopwark %2 DOS-formateert is un de
Verlöven vun de Reedschapdatei (t.B. /dev/fd0) richtig sett sünd (t.B. rwxrwxrwx).
Translated and reviewed by Sönke Dibbern on 2006-05-04
Located in kio_floppy.cpp:227
7.
Could not access %1.
The disk in drive %2 is probably not a DOS-formatted floppy disk.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Keen Togriep op %1.
Wohrschienlich is de Diskett in't Loopwark %2 nich DOS-formateert.
Translated and reviewed by Sönke Dibbern on 2006-05-04
Located in kio_floppy.cpp:231
8.
Access denied.
Could not write to %1.
The disk in drive %2 is probably write-protected.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Keen Verlööf.
Na %1 lett sik nich schrieven.
Wohrschienlich is de Diskett in %2 schriefschuult.
Translated and reviewed by Sönke Dibbern on 2006-05-04
Located in kio_floppy.cpp:235
9.
Could not read boot sector for %1.
There is probably not any disk in drive %2.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
De Systeemstartsektor op %1 lett sik nich lesen.
Wohrschienlich is dor gor keen Diskett in't Loopwark %2.
Translated and reviewed by Sönke Dibbern on 2006-05-04
Located in kio_floppy.cpp:244
10.
Could not start program "%1".
Ensure that the mtools package is installed correctly on your system.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Dat Programm "%1" lett sik nich starten.
Bitte prööv, wat dat Paket "mtools" richtig op Dien Systeem installeert is.
Translated and reviewed by Sönke Dibbern on 2006-05-04
Located in kio_floppy.cpp:368
110 of 10 results

This translation is managed by Ubuntu Low German Translators, assigned by Ubuntu Translators.

You are not logged in. Please log in to work on translations.

Contributors to this translation: Sönke Dibbern.