Browsing Ukrainian translation

3.

If the first argument passed into get is an aspect identifier matching the
format <account-id>/<bundle>/<aspect>, get will use the aspects configuration
API. In this case, the command returns the data retrieved from the requested
dot-separated aspect paths.

4.

If the first argument passed into set is an aspect identifier matching the
format <account-id>/<bundle>/<aspect>, set will use the aspects configuration
API. In this case, the command sets the values as provided for the dot-separated
aspect paths.

5.

If the first argument passed into unset is an aspect identifier matching the
format <account-id>/<bundle>/<aspect>, unset will use the aspects configuration
API. In this case, the command removes the data stored in the provided
dot-separated aspect paths.

12.

The aliases command lists all aliases available in the system and their status.

$ snap aliases <snap>

Lists only the aliases defined by the specified snap.

19.

The connections command lists connections between plugs and slots
in the system.

Unless <snap> is provided, the listing is for connected plugs and
slots for all snaps in the system. In this mode, pass --all to also
list unconnected plugs and slots.

$ snap connections <snap>

Lists connected and unconnected plugs and slots for the specified
snap.

20.

The console-conf-start command starts synchronization with console-conf

This command is used by console-conf when it starts up. It delays refreshes if
there are none currently ongoing, and exits with a specific error code if there
are ongoing refreshes which console-conf should wait for before prompting the
user to begin configuring the device.

21.

The create-cohort command creates a set of cohort keys for a given set of snaps.

A cohort is a view or snapshot of a snap's "channel map" at a given point in
time that fixes the set of revisions for the snap given other constraints
(e.g. channel or architecture). The cohort is then identified by an opaque
per-snap key that works across systems. Installations or refreshes of the snap
using a given cohort key would use a fixed revision for up to 90 days, after
which a new set of revisions would be fixed under that same cohort key and a
new 90 days window started.

27.

The disconnect command disconnects a plug from a slot.
It may be called in the following ways:

$ snap disconnect <snap>:<plug> <snap>:<slot>

Disconnects the specific plug from the specific slot.

$ snap disconnect <snap>:<slot or plug>

Disconnects everything from the provided plug or slot.
The snap name may be omitted for the core snap.

When an automatic connection is manually disconnected, its disconnected state
is retained after a snap refresh. The --forget flag can be added to the
disconnect command to reset this behaviour, and consequently re-enable
an automatic reconnection after a snap refresh.

31.

The fde-setup-request command is used inside the fde-setup hook. It will
return information about what operation for full-disk encryption is
requested and auxiliary data to complete this operation.

The fde-setup hook should do what is requested and then call
"snapctl fde-setup-result" and pass the result data to stdin.

Here is an example for how the fde-setup hook is called initially:
$ snapctl fde-setup-request
{"op":"features"}
$ echo '{"features": []}' | snapctl fde-setup-result

Alternatively the hook could reply with:
$ echo '{"error":"hardware-unsupported"}' | snapctl fde-setup-result

And then it is called again with a request to do the initial key setup:
$ snapctl fde-setup-request
{"op":"initial-setup", "key": "key-to-seal"}
$ echo "{"sealed-key":"$base64_encoded_sealed_key"}" | snapctl fde-setup-result

32.

The fde-setup-result command sets the result data for a fde-setup hook
reading it from stdin.

For example:
When the fde-setup hook is called with "op":"features:
$ echo '{"features": []}' | snapctl fde-setup-result

When the fde-setup hook is called with "op":"initial-setup":
$ echo "{"sealed-key":"$base64_encoded_sealed_key"}" | snapctl fde-setup-result