|
|
1.
|
|
|
Simulate
|
|
|
|
|
模擬
|
|
Translated by
Roy Chan
|
|
|
|
Located in
tools/k3bstdguiitems.cpp:28
|
|
|
2.
|
|
|
<p>If this option is checked K3b will perform all writing steps with the laser turned off.<p>This is useful, for example, to test a higher writing speed or whether your system is able to write on-the-fly.<p><b>Caution:</b> DVD+R(W) does not support simulated writing.
|
|
|
|
|
<p>如果勾選了此選項，K3b 會將雷射關閉並執行所有的寫入步驟。<p>舉例來說，這對於要測試更快的寫入速度或是想測試您的系統能不能以 on-the-fly 模式燒錄來說很有用。<p><b>小心：</b> DVD+R(W) 不支援模擬寫入。
|
|
Translated by
Roy Chan
|
|
|
|
Located in
tools/k3bstdguiitems.cpp:29
|
|
|
3.
|
|
|
Only simulate the writing process
|
|
|
|
|
只模擬寫入過程
|
|
Translated by
Roy Chan
|
|
|
|
Located in
tools/k3bstdguiitems.cpp:34
|
|
|
4.
|
|
|
Disk at once
|
|
|
|
|
碟片一次燒錄
|
|
Translated by
Roy Chan
|
|
|
|
Located in
tools/k3bstdguiitems.cpp:40
|
|
|
5.
|
|
|
<p>If this option is checked, K3b will write the CD in 'disk at once' mode as compared to 'track at once' (TAO).<p>It is always recommended to use DAO where possible.<p><b>Caution:</b> Track pregaps with a length other than 2 seconds are only supported in DAO mode.
|
|
|
|
|
<p>如果勾選了此選項，相較於「軌道一次燒錄（TAO）」，K3b 會以「碟片一次燒錄（DAO）」模式寫入 CD。<p>建議您總是盡可能使用 DAO 。<p><b>小心：</b>只有 DAO 模式能支援比 2 秒還長的軌道前置間隙。
|
|
Translated by
Roy Chan
|
|
|
|
Located in
tools/k3bstdguiitems.cpp:41
|
|
|
6.
|
|
|
Write in disk at once mode
|
|
|
|
|
以碟片一次燒錄模式寫入
|
|
Translated by
Roy Chan
|
|
|
|
Located in
tools/k3bstdguiitems.cpp:46
|
|
|
7.
|
|
|
Use Burnfree
|
|
|
|
|
使用 Burnfree
|
|
Translated by
Roy Chan
|
|
|
|
Located in
tools/k3bstdguiitems.cpp:52
|
|
|
8.
|
|
|
Enable Burnfree (or Just Link) to avoid buffer underruns
|
|
|
|
|
啟用 Burnfree（或稱 Just Link）以避免緩衝不敷使用
|
|
Translated by
Roy Chan
|
|
|
|
Located in
tools/k3bstdguiitems.cpp:53
|
|
|
9.
|
|
|
<p>If this option is checked, K3b enables <em>Burnfree</em> (or <em>Just Link</em>). This is a feature of the CD writer which avoids buffer underruns.<p>Without <em>burnfree</em>, if the writer cannot get any more data a buffer underrun would occurs, since the writer needs a constant stream of data to write the CD.<p>With <em>burnfree</em> the writer can <em>mark</em> the current position of the laser and get back to it when the buffer is filled again;but, since this means having little data gaps on the CD, <b>it is highly recommended to always choose an appropriate writing speed to prevent the usage of burnfree, especially for audio CDs</b> (in the worst case one would hear the gap).<p><em>Burnfree</em> was formally known as <em>Burnproof</em> but since it has become part of the MMC standard it was renamed.
|
|
|
|
|
(no translation yet)
|
|
|
|
Located in
tools/k3bstdguiitems.cpp:56
|
|
|
10.
|
|
|
Only create image
|
|
|
|
|
只建立映像檔
|
|
Translated by
Roy Chan
|
|
|
|
Located in
tools/k3bstdguiitems.cpp:73
|
