Browsing Croatian translation

Don't show this notice anymore
Before translating, be sure to go through Ubuntu Translators instructions.

These translations are shared with snapd in Ubuntu Noble template snappy.

1120 of 154 results
50.

The model command returns the active model assertion information for this
device.

By default, the model identification information is presented in a structured,
yaml-like format, but this can be changed to json by using the --json flag.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
(no translation yet)
Located in overlord/hookstate/ctlcmd/model.go:44
51.

The mount command mounts the given source onto the given destination path,
provided that the snap has a plug for the mount-control interface which allows
this operation.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
(no translation yet)
Located in overlord/hookstate/ctlcmd/mount.go:39
53.

The pack command packs the given snap-dir as a snap and writes the result to
target-dir. If target-dir is omitted, the result is written to current
directory. If both source-dir and target-dir are omitted, the pack command packs
the current directory.

The default file name for a snap can be derived entirely from its snap.yaml, but
in some situations it's simpler for a script to feed the filename in. In those
cases, --filename can be given to override the default. If this filename is
not absolute it will be taken as relative to target-dir.

When used with --check-skeleton, pack only checks whether snap-dir contains
valid snap metadata and raises an error otherwise. Application commands listed
in snap metadata file, but appearing with incorrect permission bits result in an
error. Commands that are missing from snap-dir are listed in diagnostic
messages.

When used with --append-integrity-data, pack will append dm-verity data at the end
of the snap to be used with snapd's snap integrity verification mechanism.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
(no translation yet)
Located in cmd/snap/cmd_pack.go:49
55.

The portal-info command returns information about a process in keyfile format.

This command is used by the xdg-desktop-portal service to retrieve
information about snap confined processes.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
(no translation yet)
Located in cmd/snap/cmd_routine_portal_info.go:43
59.

The quota command shows information about a quota group, including the set of
snaps and any sub-groups it contains, as well as its resource constraints and
the current usage of those constrained resources.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
There are leading/trailing spaces here. Each one represents a space character. Enter a space in the equivalent position in the translation.
(no translation yet)
Located in cmd/snap/cmd_quota.go:39
60.

The quotas command shows all quota groups.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
(no translation yet)
Located in cmd/snap/cmd_quota.go:46
61.

The reboot command can used from allowed hooks to control the reboot behavior of the system.

Currently it can only be invoked from gadget install-device during UC20 install mode. After invoking it from install-device with --halt or --poweroff the device will not reboot into run mode after finishing install mode but will instead either halt or power off. From install-device the effect is therefore not immediate but delayed until the end of installation itself.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
(no translation yet)
Located in overlord/hookstate/ctlcmd/reboot.go:31
62.

The reboot command reboots the system into a particular mode of the selected
recovery system.

When called without a system label and without a mode it will just
trigger a regular reboot.

When called without a system label but with a mode it will use the
current system to enter the given mode.

Note that "recover", "factory-reset" and "run" modes are only available for the
current system.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
(no translation yet)
Located in cmd/snap/cmd_reboot.go:43
63.

The recovery command lists the available recovery systems.

With --show-keys it displays recovery keys that can be used to unlock the encrypted partitions if the device-specific automatic unlocking does not work.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
(no translation yet)
Located in cmd/snap/cmd_recovery.go:41
64.

The refresh command prints pending refreshes of the calling snap and can hold
back disruptive refreshes of other snaps, such as refreshes of the kernel or
base snaps that can trigger a restart. This command can be used from the
gate-auto-refresh hook which is only run during auto-refresh.

Snap can query pending refreshes with:
$ snapctl refresh --pending
pending: ready
channel: stable
version: 2
revision: 2
base: false
restart: false

The 'pending' flag can be "ready", "none" or "inhibited". It is set to "none"
when a snap has no pending refreshes. It is set to "ready" when there are
pending refreshes and to ”inhibited” when pending refreshes are being
held back because more or more snap applications are running with the
“refresh app awareness” feature enabled.

The "base" and "restart" flags indicate whether the base snap is going to be
updated and/or if a restart will occur, both of which are disruptive. A base
snap update can temporarily disrupt the starting of applications or hooks from
the snap.

To tell snapd to proceed with pending refreshes:
$ snapctl refresh --pending --proceed

Note, a snap using --proceed cannot assume that the updates will occur as they
might be held back by other snaps.

To hold refresh for up to 90 days for the calling snap:
$ snapctl refresh --pending --hold
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
There are leading/trailing spaces here. Each one represents a space character. Enter a space in the equivalent position in the translation.
(no translation yet)
Located in overlord/hookstate/ctlcmd/refresh.go:56
1120 of 154 results

This translation is managed by Ubuntu Croatian Translators, assigned by Ubuntu Translators.

You are not logged in. Please log in to work on translations.

Contributors to this translation: Ante Karamatić, gogo.