Translations by Ian Li

NetworkManager needs to turn off networks

'%s' not allowed for %s=%s

property is empty'

'%s' is ambiguous (on x off)

'%s' is not a valid powersave value

WiMAX radio switch

Usage: nmcli radio wimax { ARGUMENTS | help } ARGUMENTS := [on | off] Get status of WiMAX radio switch, or turn it on/off.

Usage: nmcli radio { COMMAND | help } COMMAND := { all | wifi | wwan | wimax } all | wifi | wwan | wimax [ on | off ] COMMAND := { all | wifi | wwan } all | wifi | wwan [ on | off ]

Error: 'device wimax' command '%s' is not valid.

Error: 'device wimax': %s

Usage: nmcli device wifi { ARGUMENTS | help } Perform operation on Wi-Fi devices. ARGUMENTS := [list [ifname <ifname>] [bssid <BSSID>]] List available Wi-Fi access points. The 'ifname' and 'bssid' options can be used to list APs for a particular interface, or with a specific BSSID. ARGUMENTS := connect <(B)SSID> [password <password>] [wep-key-type key|phrase] [ifname <ifname>] [bssid <BSSID>] [name <name>] [private yes|no] Connect to a Wi-Fi network specified by SSID or BSSID. The command creates a new connection and then activates it on a device. This is a command-line counterpart of clicking an SSID in a GUI client. The command always creates a new connection and thus it is mainly useful for connecting to new Wi-Fi networks. If a connection for the network already exists, it is better to bring up the existing profile as follows: nmcli con up id <name>. Note that only open, WEP and WPA-PSK networks are supported at the moment. It is also assumed that IP configuration is obtained via DHCP. ARGUMENTS := rescan [[ifname] <ifname>] Request that NetworkManager immediately re-scan for available access points. NetworkManager scans Wi-Fi networks periodically, but in some cases it might be useful to start scanning manually. Note that this command does not show the APs, use 'nmcli device wifi list' for that.

Usage: nmcli device wimax { ARGUMENTS | help } Perform operation on WiMAX devices. ARGUMENTS := [list [ifname <ifname>] [nsp <name>]] List available WiMAX NSPs. The 'ifname' and 'nsp' options can be used to list networks for a particular interface, or with a specific NSP.

Error: bad color number: '%s'; use <0-8>

Error: 'id': '%s' is not valid; use <0-4095>.

Warning: 'type' is currently ignored. We only support ethernet slaves for now.

VLAN ID <0-4095>:

unknown error

Bond master:

Team master:

Bridge master:

invalid prefix '%s'; <1-%d> allowed

the second component of route ('%s') is neither a next hop address nor a metric

invalid metric '%s'

default route cannot be added (NetworkManager handles it by itself)

DCB or FCoE setup failed

teamd control failed

Modem failed or no longer available

Modem now ready and available

SIM PIN was incorrect

invalid priority map '%s'

priority '%s' is not valid (<0-%ld>)

'%s' is not a valid team configuration or file name.

Setting name?

Property name?

Enter connection type:

Connection type:

VPN type:

Connection (name, UUID, or path):

ACTIVE-PATH

Usage: nmcli connection modify { ARGUMENTS | help } ARGUMENTS := [id | uuid | path] <ID> ([+|-]<setting>.<property> <value>)+ Modify one or more properties of the connection profile. The profile is identified by its name, UUID or D-Bus path. For multi-valued properties you can use optional '+' or '-' prefix to the property name. The '+' sign allows appending items instead of overwriting the whole value. The '-' sign allows removing selected items instead of the whole value. Examples: nmcli con mod home-wifi wifi.ssid rakosnicek nmcli con mod em1-1 ipv4.method manual ipv4.addr "192.168.1.2/24, 10.10.1.5/8" nmcli con mod em1-1 +ipv4.dns 8.8.4.4 nmcli con mod em1-1 -ipv4.dns 1 nmcli con mod em1-1 -ipv6.addr "abbe::cafe/56" nmcli con mod bond0 +bond.options mii=500 nmcli con mod bond0 -bond.options downdelay

Usage: nmcli connection edit { ARGUMENTS | help } ARGUMENTS := [id | uuid | path] <ID> Edit an existing connection profile in an interactive editor. The profile is identified by its name, UUID or D-Bus path ARGUMENTS := [type <new connection type>] [con-name <new connection name>] Add a new connection profile in an interactive editor.

Usage: nmcli connection delete { ARGUMENTS | help } ARGUMENTS := [id | uuid | path] <ID> Delete a connection profile. The profile is identified by its name, UUID or D-Bus path.

Usage: nmcli connection reload { help } Reload all connection files from disk.

Usage: nmcli connection load { ARGUMENTS | help } ARGUMENTS := <filename> [<filename>...] Load/reload one or more connection files from disk. Use this after manually editing a connection file to ensure that NetworkManager is aware of its latest state.

Connection profile details

Error: 'connection show': %s

Activate connection details

invalid field '%s'; allowed fields: %s and %s, or %s,%s

'%s' has to be alone

NetworkManager active profiles