Browsing Brazilian Portuguese translation

Don't show this notice anymore
Before translating, be sure to go through Ubuntu Translators instructions and Brazilian Portuguese guidelines.
110 of 10 results
1.
Could not access drive %1.
The drive is still busy.
Wait until it is inactive and then try again.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Não foi possível acessar a unidade %1.
A unidade continua ocupada.
Espere até ela parar de trabalhar e tente novamente.
Translated by Jonathan Riddell on 2009-12-23
Located in kio_floppy.cpp:198
2.
Could not write to file %1.
The disk in drive %2 is probably full.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Não foi possível gravar no arquivo %1
O disco na unidade %2 provavelmente está cheio.
Translated by Luiz Fernando Ranghetti on 2009-08-04
Located in kio_floppy.cpp:202 kio_floppy.cpp:1116
3.
Could not access %1.
There is probably no disk in the drive %2
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Não foi possível acessar %1.
Não deve existir disco na unidade %2
Translated by Luiz Fernando Ranghetti on 2009-08-04
Located in kio_floppy.cpp:212
4.
Could not access %1.
There is probably no disk in the drive %2 or you do not have enough permissions to access the drive.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Não foi possível acessar %1.
Provavelmente não existe disco na unidade %2, ou você não possui permissões suficientes para acessar a unidade.
Translated by Luiz Fernando Ranghetti on 2009-08-04
Located in kio_floppy.cpp:216
5.
Could not access %1.
The drive %2 is not supported.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Não foi possível acessar %1.
A unidade %2 não é suportada.
Translated by Luiz Fernando Ranghetti on 2009-08-04
Located in kio_floppy.cpp:220
6.
Could not access %1.
Make sure the floppy in drive %2 is a DOS-formatted floppy disk
and that the permissions of the device file (e.g. /dev/fd0) are set correctly (e.g. rwxrwxrwx).
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
There are leading/trailing spaces here. Each one represents a space character. Enter a space in the equivalent position in the translation.
Não foi possível acessar %1.
Assegure-se que o disquete na unidade %2 é um disquete formatado para DOS
e que as permissões do dispositivo (exemplo: /dev/fd0) estão corretas (por exemplo: rwxrwxrwx).
Translated by Luiz Fernando Ranghetti on 2009-08-04
Located in kio_floppy.cpp:225
7.
Could not access %1.
The disk in drive %2 is probably not a DOS-formatted floppy disk.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Não foi possível acessar %1.
O disco na unidade %2 não parece estar formatado para DOS.
Translated by Luiz Fernando Ranghetti on 2009-08-04
Located in kio_floppy.cpp:229
8.
Access denied.
Could not write to %1.
The disk in drive %2 is probably write-protected.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Acesso negado.
Não foi possível gravar em %1.
O disco na unidade %2 provavelmente está protegido contra gravação.
Translated by André Marcelo Alvarenga on 2011-08-26
Located in kio_floppy.cpp:233
9.
Could not read boot sector for %1.
There is probably not any disk in drive %2.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Não foi possível ler o setor de boot para %1.
Não deve existir disco na unidade %2.
Translated by Luiz Fernando Ranghetti on 2009-08-04
Located in kio_floppy.cpp:242
10.
Could not start program "%1".
Ensure that the mtools package is installed correctly on your system.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Não foi possível iniciar o programa "%1".
Assegure-se de que o pacote mtools está devidamente instalado em seu sistema.
Translated by Lisiane Sztoltz on 2008-10-07
Located in kio_floppy.cpp:365
110 of 10 results

This translation is managed by Ubuntu Brazilian Portuguese Translators, assigned by Ubuntu Translators.

You are not logged in. Please log in to work on translations.

Contributors to this translation: André Marcelo Alvarenga, Jonathan Riddell, Lisiane Sztoltz, Luiz Fernando Ranghetti.