Browsing Brazilian Portuguese translation

Don't show this notice anymore
Before translating, be sure to go through Ubuntu Translators instructions and Brazilian Portuguese guidelines.
110 of 10 results
1.
Could not access drive %1.
The drive is still busy.
Wait until it is inactive and then try again.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Não foi possível acessar o drive %1.
O dispositivo continua ocupado.
Espere até ele parar de trabalhar e tente novamente.
Translated and reviewed by Lisiane Sztoltz on 2006-04-21
Located in kio_floppy.cpp:200
2.
Could not write to file %1.
The disk in drive %2 is probably full.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Não foi possível gravar no arquivo %1
O disco no drive %2 provavelmente está cheio.
Translated and reviewed by Lisiane Sztoltz on 2006-04-21
Located in kio_floppy.cpp:204 kio_floppy.cpp:1144
3.
Could not access %1.
There is probably no disk in the drive %2
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Não foi possível acessar %1.
Não deve existir disco no drive %2
Translated and reviewed by Lisiane Sztoltz on 2006-04-21
Located in kio_floppy.cpp:214
4.
Could not access %1.
There is probably no disk in the drive %2 or you do not have enough permissions to access the drive.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Não foi possível acessar %1.
Provavelmente não existe disco no dispositivo %2, ou você não possui permissões suficientes para acessar o dispositivo.
Translated and reviewed by Lisiane Sztoltz on 2006-04-21
Located in kio_floppy.cpp:218
5.
Could not access %1.
The drive %2 is not supported.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Não foi possível acessar %1.
O drive %2 não é suportado.
Translated and reviewed by Lisiane Sztoltz on 2006-04-21
Located in kio_floppy.cpp:222
6.
Could not access %1.
Make sure the floppy in drive %2 is a DOS-formatted floppy disk
and that the permissions of the device file (e.g. /dev/fd0) are set correctly (e.g. rwxrwxrwx).
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
There are leading/trailing spaces here. Each one represents a space character. Enter a space in the equivalent position in the translation.
Não foi possível acessar %1.
Assegure-se que o disquete no drive %2 é um disquete formatado para DOS
e que as permissões do dispositivo (exemplo: /dev/fd0) estão corretas (por exemplo: rwxrwxrwx).
Translated and reviewed by Lisiane Sztoltz on 2006-04-21
Located in kio_floppy.cpp:227
7.
Could not access %1.
The disk in drive %2 is probably not a DOS-formatted floppy disk.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Não foi possível acessar %1.
O disco no drive %2 não parece estar formatado para DOS.
Translated and reviewed by Lisiane Sztoltz on 2006-04-21
Located in kio_floppy.cpp:231
8.
Access denied.
Could not write to %1.
The disk in drive %2 is probably write-protected.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Aceso negado. Não foi possível gravar em %1.
O disco no drive %2 provavelmente está protegido contra gravação.
Translated and reviewed by Lisiane Sztoltz on 2006-04-21
Located in kio_floppy.cpp:235
9.
Could not read boot sector for %1.
There is probably not any disk in drive %2.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Não foi possível ler o setor de boot para %1.
Não deve existir disco no drive %2.
Translated and reviewed by Lisiane Sztoltz on 2006-04-21
Located in kio_floppy.cpp:244
10.
Could not start program "%1".
Ensure that the mtools package is installed correctly on your system.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Não foi possível iniciar o programa "%1".
Assegure-se de que o pacote mtools está devidamente instalado em seu sistema.
Translated and reviewed by Lisiane Sztoltz on 2006-04-21
Located in kio_floppy.cpp:368
110 of 10 results

This translation is managed by Ubuntu Brazilian Portuguese Translators, assigned by Ubuntu Translators.

You are not logged in. Please log in to work on translations.

Contributors to this translation: Lisiane Sztoltz.