Browsing Czech translation

Don't show this notice anymore
Before translating, be sure to go through Ubuntu Translators instructions and Czech guidelines.
110 of 10 results
1.
Could not access drive %1.
The drive is still busy.
Wait until it is inactive and then try again.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Nelze přistupovat k mechanice %1.
Mechanika je stále v činnosti.
Počkejte, až činnost dokončí a zkuste znovu.
Translated and reviewed by Lukáš Tinkl on 2006-04-21
Located in kio_floppy.cpp:200
2.
Could not write to file %1.
The disk in drive %2 is probably full.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Nelze zapisovat do souboru %1.
Disk v mechanice %2 je pravděpodobně plný.
Translated and reviewed by Lukáš Tinkl on 2006-04-21
Located in kio_floppy.cpp:204 kio_floppy.cpp:1144
3.
Could not access %1.
There is probably no disk in the drive %2
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Nelze přistupovat k %1.
V mechanice %2 není pravděpodobně disk.
Translated and reviewed by Lukáš Tinkl on 2006-04-21
Located in kio_floppy.cpp:214
4.
Could not access %1.
There is probably no disk in the drive %2 or you do not have enough permissions to access the drive.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Nelze přistupovat k %1.
V mechanice %2 pravděpodobně není disketa nebo nemáte dostatečná oprávnění pro přístup k zařízení.
Translated and reviewed by Lukáš Tinkl on 2006-04-21
Located in kio_floppy.cpp:218
5.
Could not access %1.
The drive %2 is not supported.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Nelze přistupovat k %1.
Mechanika %2 není podporována.
Translated and reviewed by Lukáš Tinkl on 2006-04-21
Located in kio_floppy.cpp:222
6.
Could not access %1.
Make sure the floppy in drive %2 is a DOS-formatted floppy disk
and that the permissions of the device file (e.g. /dev/fd0) are set correctly (e.g. rwxrwxrwx).
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
There are leading/trailing spaces here. Each one represents a space character. Enter a space in the equivalent position in the translation.
Nelze přistupovat k %1.
Ujistěte se, že disketa v mechanice %2 je naformátována pomocí DOSu
a že jsou správně nastavena oprávnění na souboru zařízení (např. /dev/fd0) na rwxrwxrwx.
Translated and reviewed by Lukáš Tinkl on 2006-04-21
Located in kio_floppy.cpp:227
7.
Could not access %1.
The disk in drive %2 is probably not a DOS-formatted floppy disk.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Nelze přistupovat k %1.
Disketa v mechanice %2 není pravděpodobně naformátovaná pomocí DOSu.
Translated and reviewed by Lukáš Tinkl on 2006-04-21
Located in kio_floppy.cpp:231
8.
Access denied.
Could not write to %1.
The disk in drive %2 is probably write-protected.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Přístup odmítnut.
Nelze zapisovat do %1.
Disketa v mechanice %2 je pravděpodobně chráněna proti zápisu.
Translated and reviewed by Lukáš Tinkl on 2006-04-21
Located in kio_floppy.cpp:235
9.
Could not read boot sector for %1.
There is probably not any disk in drive %2.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Nelze přečíst startovací sektor %1.
V mechanice %2 není pravděpodobně disk.
Translated and reviewed by Lukáš Tinkl on 2006-04-21
Located in kio_floppy.cpp:244
10.
Could not start program "%1".
Ensure that the mtools package is installed correctly on your system.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Nelze spustit program "%1".Ujistěte se, že máte na svém systému nainstalován balík mtools.
Translated and reviewed by Lukáš Tinkl on 2006-04-21
Located in kio_floppy.cpp:368
110 of 10 results

This translation is managed by Ubuntu Czech Translators, assigned by Ubuntu Translators.

You are not logged in. Please log in to work on translations.

Contributors to this translation: Lukáš Tinkl.