Browsing Slovak translation

Don't show this notice anymore
Before translating, be sure to go through Ubuntu Translators instructions.
110 of 10 results
1.
Could not access drive %1.
The drive is still busy.
Wait until it is inactive and then try again.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Nie je možný prístup k mechanike %1.
Disketa je ešte stále zaneprázdnená.
Počkajte, kým prestane pracovať a potom to skúste znovu.
Translated and reviewed by Stanislav Visnovsky on 2006-04-21
Located in kio_floppy.cpp:200
2.
Could not write to file %1.
The disk in drive %2 is probably full.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Nepodarilo sa zapísať súbor %1.
Disketa v mechanike %2 je asi plná.
Translated and reviewed by Stanislav Visnovsky on 2006-04-21
Located in kio_floppy.cpp:204 kio_floppy.cpp:1144
3.
Could not access %1.
There is probably no disk in the drive %2
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Nepodaril sa prístup k %1.
V mechanike %2 asi nie je disketa
Translated and reviewed by Stanislav Visnovsky on 2006-04-21
Located in kio_floppy.cpp:214
4.
Could not access %1.
There is probably no disk in the drive %2 or you do not have enough permissions to access the drive.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Nepodaril sa prístup k %1.
V jednotke %2 nieje pravdepodobne vložený disk alebo nemáte dostatočné prístupove práva pre prístup k tejto jednotke.
Translated by Stanislav Visnovsky on 2006-04-21
Reviewed by Jose Riha on 2007-06-03
Located in kio_floppy.cpp:218
5.
Could not access %1.
The drive %2 is not supported.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Nepodaril sa prístup k %1.
Mechanika %2 nie je podporovaná.
Translated and reviewed by Stanislav Visnovsky on 2006-04-21
Located in kio_floppy.cpp:222
6.
Could not access %1.
Make sure the floppy in drive %2 is a DOS-formatted floppy disk
and that the permissions of the device file (e.g. /dev/fd0) are set correctly (e.g. rwxrwxrwx).
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
There are leading/trailing spaces here. Each one represents a space character. Enter a space in the equivalent position in the translation.
Nepodaril sa prístup k %1.
Overte, že disketa v mechanike %2 je pre DOS
a že práva na súbore zariadenia (napr. /dev/fd0) sú správne (napr. rwxrwxrwx).
Translated and reviewed by Stanislav Visnovsky on 2006-04-21
Located in kio_floppy.cpp:227
7.
Could not access %1.
The disk in drive %2 is probably not a DOS-formatted floppy disk.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Nepodaril sa prístup k %1.
Disketa v mechanike %2 asi nie je naformátovaná ako DOS disketa.
Translated and reviewed by Stanislav Visnovsky on 2006-04-21
Located in kio_floppy.cpp:231
8.
Access denied.
Could not write to %1.
The disk in drive %2 is probably write-protected.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Prístup odmietnutý.
Nepodaril sa zápis do %1.
Disketa v mechanike %2 je asi chránená proti zápisu.
Translated and reviewed by Stanislav Visnovsky on 2006-04-21
Located in kio_floppy.cpp:235
9.
Could not read boot sector for %1.
There is probably not any disk in drive %2.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Nepodarilo sa prečítať bootovací sektor pre %1.
V mechanike %2 asi nie je disketa.
Translated and reviewed by Stanislav Visnovsky on 2006-04-21
Located in kio_floppy.cpp:244
10.
Could not start program "%1".
Ensure that the mtools package is installed correctly on your system.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Nepodarilo sa spustiť program "%1".
Overte, že máte správne nainštalovaný balík mtools.
Translated and reviewed by Stanislav Visnovsky on 2006-04-21
Located in kio_floppy.cpp:368
110 of 10 results

This translation is managed by Ubuntu Slovak Translators, assigned by Ubuntu Translators.

You are not logged in. Please log in to work on translations.

Contributors to this translation: Stanislav Visnovsky.