Browsing Portuguese translation

Don't show this notice anymore
Before translating, be sure to go through Ubuntu Translators instructions and Portuguese guidelines.
110 of 10 results
1.
Could not access drive %1.
The drive is still busy.
Wait until it is inactive and then try again.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Não foi possível aceder a unidade %1.
A unidade continua ocupada.
Espere até ela ter parado de trabalhar e tente de novo.
Translated and reviewed by José Nuno Pires on 2006-04-21
Located in kio_floppy.cpp:200
2.
Could not write to file %1.
The disk in drive %2 is probably full.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Não foi possível escrever no ficheiro %1.
O disco na unidade %2 está provavelmente cheio.
Translated and reviewed by José Nuno Pires on 2006-04-21
Located in kio_floppy.cpp:204 kio_floppy.cpp:1144
3.
Could not access %1.
There is probably no disk in the drive %2
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Não foi possível aceder a %1.
Não deve estar nenhum disco na unidade %2
Translated and reviewed by José Nuno Pires on 2006-04-21
Located in kio_floppy.cpp:214
4.
Could not access %1.
There is probably no disk in the drive %2 or you do not have enough permissions to access the drive.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Não foi possível aceder a %1
Provavelmente não está qualquer disco na unidade %2 ou não tem permissão para aceder a esta unidade.
Translated and reviewed by José Nuno Pires on 2006-04-21
Located in kio_floppy.cpp:218
5.
Could not access %1.
The drive %2 is not supported.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Não foi possível aceder a %1.
A unidade %2 não é suportada.
Translated and reviewed by José Nuno Pires on 2006-04-21
Located in kio_floppy.cpp:222
6.
Could not access %1.
Make sure the floppy in drive %2 is a DOS-formatted floppy disk
and that the permissions of the device file (e.g. /dev/fd0) are set correctly (e.g. rwxrwxrwx).
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
There are leading/trailing spaces here. Each one represents a space character. Enter a space in the equivalent position in the translation.
Não foi possível aceder a %1.
Verifique se a disquete na unidade %2 é mesmo uma disquete formatada em DOS
e que as permissões do dispositivo (p.ex. /dev/fd0) estão correctas (p.ex. rwxrwxrwx).
Translated and reviewed by José Nuno Pires on 2006-04-21
Located in kio_floppy.cpp:227
7.
Could not access %1.
The disk in drive %2 is probably not a DOS-formatted floppy disk.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Não foi possível aceder a %1.
O disco na unidade %2 não parece estar formatado para o DOS.
Translated and reviewed by José Nuno Pires on 2006-04-21
Located in kio_floppy.cpp:231
8.
Access denied.
Could not write to %1.
The disk in drive %2 is probably write-protected.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Acesso negado.
Não foi possível escrever em %1.
O disco na unidade %2 está provavelmente protegido contra gravações.
Translated and reviewed by José Nuno Pires on 2006-04-21
Located in kio_floppy.cpp:235
9.
Could not read boot sector for %1.
There is probably not any disk in drive %2.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Não possível ler o sector de arranque de %1.
Provavelmente não está nenhum disco na unidade %2.
Translated and reviewed by José Nuno Pires on 2006-04-21
Located in kio_floppy.cpp:244
10.
Could not start program "%1".
Ensure that the mtools package is installed correctly on your system.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
Não foi possível iniciar o programa "%1".
Verifique se o pacote mtools está devidamente instalado no sistema.
Translated and reviewed by José Nuno Pires on 2006-04-21
Located in kio_floppy.cpp:368
110 of 10 results

This translation is managed by Ubuntu Portuguese Translators, assigned by Ubuntu Translators.

You are not logged in. Please log in to work on translations.

Contributors to this translation: José Nuno Pires.