Browsing Japanese translation

Don't show this notice anymore
Before translating, be sure to go through Ubuntu Translators instructions and Japanese guidelines.
110 of 10 results
1.
Could not access drive %1.
The drive is still busy.
Wait until it is inactive and then try again.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
ドライブ %1 は、アクセスできません
このドライブはビジーです。
ドライブが停止するまで待ってから再試行して下さい。
Translated and reviewed by Toyohiro Asukai on 2006-04-21
Shared:
ドライブ %1 にアクセスできませんでした。
このドライブはビジーです。
ドライブが停止するまで待ってから再試行してください。
Suggested by Yukiko Bando on 2007-03-06
Located in kio_floppy.cpp:200
2.
Could not write to file %1.
The disk in drive %2 is probably full.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
ファイル %1に書き込めません
おそらくドライブ %2 は満杯です。
Translated and reviewed by Toyohiro Asukai on 2006-04-21
Located in kio_floppy.cpp:204 kio_floppy.cpp:1144
3.
Could not access %1.
There is probably no disk in the drive %2
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
%1 にアクセスできません
おそらくドライブ %2 にディスクがありません
Translated and reviewed by Toyohiro Asukai on 2006-04-21
Shared:
%1 にアクセスできません
おそらくドライブ %2 にディスクがありません
Suggested by Toyohiro Asukai on 2006-04-21
Located in kio_floppy.cpp:214
4.
Could not access %1.
There is probably no disk in the drive %2 or you do not have enough permissions to access the drive.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
%1 にアクセスできません
おそらくドライブ %2 にはディスクがないか、ドライブにアクセスする権限が不足しているのでしょう。
Translated and reviewed by Toyohiro Asukai on 2006-04-21
Located in kio_floppy.cpp:218
5.
Could not access %1.
The drive %2 is not supported.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
%1 にアクセスできません
ドライブ%2はサポートされていません。
Translated and reviewed by Toyohiro Asukai on 2006-04-21
Shared:
%1 にアクセスできません
ドライブ%2はサポートされていません。
Suggested by Toyohiro Asukai on 2006-04-21
Located in kio_floppy.cpp:222
6.
Could not access %1.
Make sure the floppy in drive %2 is a DOS-formatted floppy disk
and that the permissions of the device file (e.g. /dev/fd0) are set correctly (e.g. rwxrwxrwx).
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
There are leading/trailing spaces here. Each one represents a space character. Enter a space in the equivalent position in the translation.
%1 にアクセスできません
ドライブ%2にあるフロッピーディスクがDOSフォーマットであり、
デバイスファイル(例 /dev/fd0)が正しく(例 rwxrwxrwx)セットされているか 確認して下さい。
Translated and reviewed by Toyohiro Asukai on 2006-04-21
Located in kio_floppy.cpp:227
7.
Could not access %1.
The disk in drive %2 is probably not a DOS-formatted floppy disk.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
%1 にアクセスできません
おそらくドライブ%2のディスクはDOSフォーマットではありません。
Translated and reviewed by Toyohiro Asukai on 2006-04-21
Located in kio_floppy.cpp:231
8.
Access denied.
Could not write to %1.
The disk in drive %2 is probably write-protected.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
アクセスを拒否
%1 に書き込みできません
おそらくドライブ%2のディスクは書き込み不可になっています。
Translated and reviewed by Toyohiro Asukai on 2006-04-21
Shared:
アクセスを拒否
%1 に書き込みできません
おそらくドライブ%2のディスクは書き込み不可になっています。
Suggested by Toyohiro Asukai on 2006-04-21
Located in kio_floppy.cpp:235
9.
Could not read boot sector for %1.
There is probably not any disk in drive %2.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
%1のためにブートセクターを読めません
おそらくドライブ%2にディスクがありません
Translated and reviewed by Toyohiro Asukai on 2006-04-21
Shared:
%1のためにブートセクターを読めません
おそらくドライブ%2にディスクがありません
Suggested by Toyohiro Asukai on 2006-04-21
Located in kio_floppy.cpp:244
10.
Could not start program "%1".
Ensure that the mtools package is installed correctly on your system.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
プログラム %1 を実行できません
システムにmtoolsパッケージが正しくインストールされているか確認して下さい。
Translated and reviewed by Toyohiro Asukai on 2006-04-21
Located in kio_floppy.cpp:368
110 of 10 results

This translation is managed by Ubuntu Japanese Translators, assigned by Ubuntu Translators.

You are not logged in. Please log in to work on translations.

Contributors to this translation: Toyohiro Asukai, Yukiko Bando.