Translations by Alem Kožljak

'%s' is ambiguous (%s x %s)

Editor failed with signal %d

Editor failed with status %d

Error in configuration file: %s.

Ignoring unrecognized log domain(s) '%s' from config files.

'%s' is not valid; use 0, 1, or 2

Error: invalid property '%s': %s.

Error: failed to modify %s.%s: %s.

Error: invalid or not allowed setting '%s': %s.

Error: invalid <setting>.<property> '%s'.

Error: value for '%s' argument is required.

goto <setting>[.<prop>] | <prop> :: enter setting/property for editing This command enters into a setting or property for editing it. Examples: nmcli> goto connection nmcli connection> goto secondaries nmcli> goto ipv4.addresses

remove <setting>[.<prop>] :: remove setting or reset property value This command removes an entire setting from the connection, or if a property is given, resets that property to the default value. Examples: nmcli> remove wifi-sec nmcli> remove eth.mtu

set [<setting>.<prop> <value>] :: set property value This command sets property value. Example: nmcli> set con.id My connection

describe [<setting>.<prop>] :: describe property Shows property description. You can consult nm-settings(5) manual page to see all NM settings and properties.

print [all] :: print setting or connection values Shows current property or the whole connection. Example: nmcli ipv4> print all

save [persistent|temporary] :: save the connection Sends the connection profile to NetworkManager that either will save it persistently, or will only keep it in memory. 'save' without an argument means 'save persistent'. Note that once you save the profile persistently those settings are saved across reboot or restart. Subsequent changes can also be temporary or persistent, but any temporary changes will not persist across reboot or restart. If you want to fully remove the persistent connection, the connection profile must be deleted.

activate [<ifname>] [/<ap>|<nsp>] :: activate the connection Activates the connection. Available options: <ifname> - device the connection will be activated on /<ap>|<nsp> - AP (Wi-Fi) or NSP (WiMAX) (prepend with / when <ifname> is not specified)

remove [<value>|<index>|<option name>] :: delete the value Removes the property value. For single-valued properties, this sets the property back to its default value. For container-type properties, this removes all the values of that property, or you can specify an argument to remove just a single item or option. The argument is either a value or index of the item to remove, or an option name (for properties with named options). Examples: nmcli ipv4.dns> remove 8.8.8.8 nmcli ipv4.dns> remove 2 nmcli bond.options> remove downdelay

Error: '%s' setting not present in the connection

, neither a valid setting name

Verify setting '%s': %s

Verify connection: %s

Error: connection is not saved. Type 'save' first.

Error: Cannot activate connection: %s.

Monitoring connection activation (press any key to continue)

Error: save-confirmation: %s

Warning: editing existing connection '%s'; 'type' argument is ignored

Warning: editing existing connection '%s'; 'con-name' argument is ignored

Valid connection types: %s

Error: invalid connection type; %s

Connection '%s' (%s) successfully modified.

Error: cannot delete unknown connection(s): %s.

Could not load file '%s'

Error: No arguments provided.

Usage: nmcli device status { help } Show status for all devices. By default, the following columns are shown: DEVICE - interface name TYPE - device type STATE - device state CONNECTION - connection activated on device (if any) Displayed columns can be changed using '--fields' global option. 'status' is the default command, which means 'nmcli device' calls 'nmcli device status'.

Error: invalid extra argument '%s'.

Error: Device activation failed: device was disconnected

Wi-Fi scan list

portal

limited

full

Error: '--fields' value '%s' is not valid here (allowed field: %s)

Error: invalid '%s' argument: '%s' (use on/off).

Connectivity

Error: 'networking' command '%s' is not valid.

Do you also want to set '%s' to '%s'? [yes]:

Do you also want to clear '%s'? [yes]:

Warning: %s.%s set to '%s', but it might be ignored in infrastructure mode

Warning: %s is not an UUID of any existing connection profile