Ndisc6

Browsing Occitan (post 1500) translation

  1. Series trunk
  2. Template “ndisc6”
  3. Occitan (post 1500) (oc)
Don't show this notice anymore
Before translating, be sure to go through Launchpad Translators instructions.

These translations are shared with ndisc6 in Ubuntu Noble template ndisc6.

1 → 4 of 4 results First • Previous • Next • Last
76.
Warning: "%s" is too small (%zu %s) to fill block of %zu %s.
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
(no translation yet)
Located in src/tcpspray.c:152
85.

-4 force usage of the IPv4 protocols family
-6 force usage of the IPv6 protocols family
-b specify the block bytes size (default: 1024)
-d wait for given delay (usec) between each block (default: 0)
-e perform a duplex test (TCP Echo instead of TCP Discard)
-f fill sent data blocks with the specified file content
-h display this help and exit
-n specify the number of blocks to send (default: 100)
-V display program version and exit
-v enable verbose output
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
There are leading/trailing spaces here. Each one represents a space character. Enter a space in the equivalent position in the translation.
(no translation yet)
Located in src/tcpspray.c:283
89.

-A send TCP ACK probes
-d enable socket debugging
-E set TCP Explicit Congestion Notification bits in probe packets
-f specify the initial hop limit (default: 1)
-g insert a route segment within a "Type 0" routing header
-h display this help and exit
-i force outgoing network interface
-l set probes byte size
-m set the maximum hop limit (default: 30)
-N perform reverse name lookups on the addresses of every hop
-n don't perform reverse name lookup on addresses
-p override source TCP port
-q override the number of probes per hop (default: 3)
-r do not route packets
-S send TCP SYN probes (default)
-s specify the source IPv6 address of probe packets
-t set traffic class of probe packets
-V, --version display program version and exit
-w override the timeout for response in seconds (default: 5)
-z specify a time to wait (in ms) between each probes (default: 0)
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
There are leading/trailing spaces here. Each one represents a space character. Enter a space in the equivalent position in the translation.
(no translation yet)
Located in src/tcptraceroute.c:53
103.

-A send TCP ACK probes
-d enable socket debugging
-E set TCP Explicit Congestion Notification bits in TCP packets
-f specify the initial hop limit (default: 1)
-g insert a route segment within a "Type 0" routing header
-h display this help and exit
-I use ICMPv6 Echo Request packets as probes
-i force outgoing network interface
-l display incoming packets hop limit
-m set the maximum hop limit (default: 30)
-N perform reverse name lookups on the addresses of every hop
-n don't perform reverse name lookup on addresses
-p override destination port
-q override the number of probes per hop (default: 3)
-r do not route packets
-S send TCP SYN probes
-s specify the source IPv6 address of probe packets
-t set traffic class of probe packets
-U send UDP probes (default)
-V display program version and exit
-w override the timeout for response in seconds (default: 5)
-z specify a time to wait (in ms) between each probes (default: 0)
There are line breaks here. Each one represents a line break. Start a new line in the equivalent position in the translation.
There are leading/trailing spaces here. Each one represents a space character. Enter a space in the equivalent position in the translation.
(no translation yet)
Located in src/traceroute.c:1219
1 → 4 of 4 results First • Previous • Next • Last

This translation is managed by translation group launchpad-translators.

You are not logged in. Please log in to work on translations.

Contributors to this translation: Cédric VALMARY (Tot en òc).